activeitup 
Nowadays, there are so many products of induction heating module in the market and you are wondering to choose a best one. You have searched for induction heating module in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings induction heating module which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
sainsmart 5V~12V Zero Voltage Switching ZVS Induction Heating Power Supply Module + Coil Power Supply Heating Power Supply Module
- ZVS heating power supply module includes the heating coil.
- Input voltage DC5V-12V.
- Maximum power 120W.(when 12V eddy-current heating)
- Ensure all the components welding right, power line connect in the right way.
- The width of the heated object is as far as possible between the 1/3~1/2 of the inner diameter of the heating coil, the maximum width is less than 2/3.
Parameters:
1. This is no tap mini plate ZVS finished board, with no heating coil, ignition coil, and a cooling fan, etc.
2. The input voltage is DC 5-12V.
3. PCB size: 55 mm * 37 mm * 1.6 mm.
Package List:
1 x ZVS heating power supply module
Note: the product is ZVS heating power supply module, includes the heating coil
1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan
- The induction heating boards maximum power is 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
- The induction heating circuit adopt 12-48V DC power supply, maximum current is 40A, the power uo to 1800W. It can work continuously under the condition of good heat dissipation. moderate power which make it can be used to quenching, annealing and other heat treatment. also for melted with graphite crucible kim/silver/ copper/aluminum and so on, heating is evenly and fast
- it is recommended that not exceed 48V 35A to prevent accidents and damage,Although withstand more than 40A current.Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small almost without response, and 12V power might lead to the voltage decreases, which is very dangerous.More than 24V/20A power supply, the greater the voltage/current, the greater the heating power, heating faster.
- please check the power output meets the requirements if the MOS tube fever,and be sure to do a good job of cooling.Do not empty the board, otherwise it will create a very high noise, then MOS tube will burn out
- please do not to heat too large metal, otherwise it may be overloaded, please add a 35A fuse or ammeter and air switch for better use (not included).
Specification:
Product size:Approx.180x90x80mm (please allowed 1-3mm error)
Heater ring inner:70mm (Recommended crucible+quartz suit,maximum support of 58mm crucible)
Power supply:
New style :AC 100-220V Adapter
Old style: Main board Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
NOTE:New style and Old style shipped by randomly!!!
It doesn’t affect the performance of product.!!!
Maximum power: 1800W
Maximum current: 40A
Package Content:
1 x PCB board
1 x 48V copper tube
1.The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. you can buy a small water pump and 2 meters of rubber hose(inner diameter is 4mm) for build a water cooling system
Please pay attention to using switch power supply, because output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit that will be lead to circuit can’t afford to vibrate caused by lacking voltage,so that the two MOS tube conduction and components will burned
comes with heating circle diameter-60 mm/design voltage-36V,if you use more than 40V Devices shall be used ≥70 mm diameter heating ring, DC 12V water pump use, please use separate power supply voltage regulator module to avoid fan and water pump are burn out
The minimum input is 12V, but it doesn’t mean all 12V power supply available,The module has specific requirements on voltage and current , 12V require current must than 10A ,output power will greatly reduced if the power is too low ,which will lead to two MOS conduction at the same time & burn MOS tube when lower than 12V
DC 12V-24V 1000W 50 A ZVS Low Voltage High Frequency Induction Heating Module Board with Tesla Coil and Cooling Fan
- Input voltage DC 12V ~ 40V, maximum input current 50A (short), recommended Input voltage range DC 24V ~ 36V
- The power supply used for heating must be large enough
- Using a protective power supply, don’t use battery or battery power
- For long time use, brass tube with water must be used for cooling
- This one is mainly used for heating
Note: It is the working voltage work, the input voltage when the coil is connected or heated. Not the no load voltage. When 12V for power supply, the current should be no less than 20A; when 24V for power supply, the current should be no less than 30A; when 36V for power supply, the current should be no less than 50A. For long time use, brass tube with water must be used for cooling.Output port copper cylinder can most install copper tube of 10mm diameter; when the copper diameter is no more than 4mm, you can solder the copper tube on the clip then fix the copper cylinder; when the diameter is no more than 2mm, it can be connected with output terminal.
This one is mainly used for heating, suitable for the heating power is less than 300W.
Specifications:
Input Voltage: DC 12-40V
Max Input Current: 50A (short time)
PCB Size: 16.5 x 11.2cm/6.5 x 4.4 inch
Board thickness: 0.16cm/0.063inch(only board)
Weight: 780g
Package Included:
1 x induction heating module
1 x brass tube
1 set x brass cylinder and screw
ZVS Driver Module,5V-12V ZVS Low Voltage Induction Heating Power Supply Board+Heating Coil
- ZVS heating power supply module including 1pcs heating coil
- Input voltage- DC 5V-12V
- Max Power-120W (when 12V induction heating)
- Ensure all the components welding right,power line connect in right way,than to set up an electric circuit
- Width of the heated object : as far as possible 1/3~1/2 , maximum inner diameter of the heating coil: not more than 2/3
- PCB size: 55 mmx37 mmx1.6 mm
Specification:
Input voltage: DC 5v-12 v
Maximum power 120w (12 v induction heating). 12 v, push the ignition coil primary 5 + 5 turn, about 30 w.
PCB size: 55 mmx37 mmx1.6 mm
Heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most not more than two-thirds.
Package Included:
1 x ZVS driver board
1 x heating coil
HiLetgo ZVS 20A 1000W Low Voltage Induction Heating Module Flyback Heater Driver Board
Description:
This section of induction heating using low-voltage DC power supply 12-48V
Maximum current 20A, maximum power 1000W.
Tested 53V power supply when working properly.
Because of its moderate power, can be used for small parts DIY players do hardening, annealing and other heat treatment,
Also can be used with a graphite crucible melting gold, silver, copper, aluminum and other metals,uniform heating fast, very convenient.
24V input with no load current of 3A
48V input with no load current of 6A
The higher the voltage, the greater the heating current when the same thing, the effect is better,
But at the same time heat is also large, so to eradicate the actual situation to select the input voltage,
the general use of the words 24V or 36V power supply is enough.
This circuit can not only do the induction heating, the copper tube into the high-frequency transformer, is a powerful inverter
1. To increase the heat sink using a customized substrate as thick as 8.5mm!
Cooling capacity is very powerful.
2.Using the M4 pillars, fever smaller, more efficient.
1000W 20A ZVS Low Voltage Induction Heating Board Module Tesla with Coil 12V-48V Flyback Driver Heater DIY
- 12-48V low voltage power supply. Maximum current 20A, Maximum power 1000W.The bigger voltage, the higher power.
- Tested 53V power supply when working properly. It can be used for DIY players to make small parts quenching, annealing and other heat treatment, heating fast, very convenient
- This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter
- The higher voltage, the higher current when heating the same things, the effect is better, but at the same time heating is also higher, therefore the choice of input voltage is based on your need.24V or 36V power supply is enough
- Note: buyer need to bring their own power and cooling unit
Features:
24V input with no load current of 3A , 48V input with no load current of 6A
buyer need self-provided power and water cooling device
This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter
Note:
The kit contains a full set of driving circuit elements and brass
Buyers need to bring their own power and cooling unit.
The circuit board using double-sided fiberglass board, mainly copper traces are used to widen use the entire back surface of the resonant circuit common, continuous work, please add a fan to blow down from above, to the resonance capacitors and other components cool.
The use of switching power supply Please note that due to high power are generally slow start function, which just opened machine output voltage is slowly rising, while it is turned on before the induction heating circuit if the voltage rises to 12V, because start insufficient voltage can not afford to vibration, resulting in two simultaneous conduction mos tube so burned components.
So the first will start switching power supply voltage reaches 12V above and then access the induction heating circuit.
The volume of the object being heated inside the heating coil can not exceed 1/5 of the volume (if the heating cylinder, then heating coil diameter less than the diameter of 1/3), or it may be due to overload or burn out the power supply to the circuit.
Although this circuit can tolerate 20-30A input current moment, but do not exceed 15A when safe work, you can easily add an ammeter between the power supply and heating driver board but always monitor the current overload
Package Includes:
1 x 20A 1000W Flyback driver inductive heater Zero Voltage Switching Tesla
1 x Coil
ILS – 5V -12V ZVS Induction Heating Power Supply Module with Coil
Features:
Input voltage: 5v-12vModule dimensions: 5.5 x 4 x 2 cm(L*W*H)Coil size: length:7.5cm width: 2.8cm
Package Included:
1 x induction heating power supply module1 x coil
fosa 2000W Induction Heating Module ZVS High Voltage 24V-70V Induction Heating Board Flyback Driver Heater DIY High Frequency Induction Heating Machine Module
Professional ZVS Low Voltage Induction Heating Power Supply Module 5V-12V 120W Induction Heating Board with Coil
- One of best heating power supply module.
- The product includes heating coil.
- Input voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V).
- Maximum power 120W(when 12V eddy-current heating).
- Ensure all the components welding right, power line connect in right way,than to set up an electric circuit.
Features:
One of best heating power supply module.
The product includes heating coil.
Input voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V).
Maximum power 120W(when 12V eddy-current heating).
Ensure all the components welding right, power line connect in right way,than to set up an electric circuit.
Descriptions:
The width of the heated object is as far as possible between the 1/3~1/2 of the inner diameter of the heating coil, the maximum not more than 2/3.
Specifications:
Input voltage: 5v-12v
Module dimensions: 5.5*4*2 cm
Coil size: length:7.5cm
width: 2.8cm
Color: black
Package Contents:
1 x Heating Power Supply Module
Notes:
The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
Conclusion
By our suggestions above, we hope that you can found induction heating module for you.Please don’t forget to share your experience by comment in this post. Thank you!
